Skip to content
    Deepvac
    Products - Custom TVAC

    Application-Specific Thermal Vacuum Engineering

    When standard chamber platforms cannot meet your test requirements, Deepvac develops fully custom thermal vacuum systems, engineered from concept through commissioning around your specific geometry, thermal profile, instrumentation, and integration constraints. Custom configurations cover volumes below and above the standard series and ultimate pressures down to the 10⁻⁷ mbar range.

    Start technical questionnaireTalk to an engineer

    For detailed custom TVAC and space-simulation requirements. Around 10 to 15 minutes. Unknown fields can remain blank.

    EngineeringBespokeIntegrationFull SystemSupportConcept to Operation
    Deepvac Custom Thermal Vacuum Chamber System

    Custom thermal vacuum chamber, engineered, integrated, and commissioned by Deepvac.

    Project Drivers

    When Standard Isn't Enough

    Custom thermal vacuum systems are engineered when your application demands capabilities, geometries, or integration requirements beyond the scope of standardised chamber platforms.

    Non-Standard Geometries

    Test articles that exceed standard chamber dimensions or require specialised access, orientation, or mounting configurations.

    Specific Thermal Profiles

    Applications demanding precise temperature ranges, ramp rates, uniformity requirements, or multi-zone thermal control.

    Complex Feedthrough Requirements

    Electrical, optical, fluid, or mechanical feedthrough configurations that exceed standard port layouts.

    Contamination-Sensitive Testing

    Hardware requiring low-outgassing environments, clean interfaces, and controlled material compatibility.

    Specialised Control Architecture

    Custom automation logic, advanced data acquisition, or integration with existing facility control systems.

    Subsystem & Interface Constraints

    Integration with existing infrastructure, specific utility connections, or project-defined mechanical and electrical interfaces.

    Have a Specific Test Requirement?

    Deepvac's engineering team can help evaluate your requirements and develop a system concept.

    Configure your TVAC systemRequest a Technical Consultation

    Prefer a direct conversation?

    System Configuration

    Configurable System Dimensions

    Every custom TVAC system is defined across multiple engineering dimensions to match your specific application requirements.

    Chamber Geometry

    • Custom dimensions and volumes
    • Horizontal or vertical orientation
    • Application-specific access ports
    • Multi-door or removable end-cap configurations

    Thermal System

    • Shroud and platen design
    • Multi-zone thermal control
    • Application-specific temperature ranges
    • Bake-out capability

    Vacuum Architecture

    • Pumping train configuration
    • Application-dependent pressure regimes
    • Leak-tight chamber design
    • Clean vacuum environments

    Instrumentation & Control

    • Sensor and measurement integration
    • Custom automation and HMI
    • Data acquisition systems
    • Remote monitoring capability

    Feedthroughs & Interfaces

    • Electrical and signal feedthroughs
    • Fluid and gas connections
    • Optical access ports
    • Mechanical motion feedthroughs

    Integration & Infrastructure

    • Facility interface engineering
    • Utility and service connections
    • Fixture and mounting systems
    • Safety and interlock integration
    Project Workflow

    From Concept to Commissioning

    Deepvac supports the full development lifecycle of custom thermal vacuum systems, from initial requirements discussion through engineering, manufacturing, and installation.

    01

    Requirements Discussion

    Technical consultation to understand your test requirements, payload characteristics, operational constraints, and integration context.

    02

    Concept & System Design

    Engineering concept development including chamber geometry, thermal architecture, vacuum design, instrumentation, and control system specification.

    03

    Detailed Engineering

    Detailed mechanical, electrical, and control system design with documentation, interface specifications, and design review milestones.

    04

    Manufacturing & Assembly

    Precision manufacturing, subsystem assembly, and integration with quality control and testing throughout the build process.

    05

    Commissioning & Support

    Delivery, installation, acceptance testing, operator training, and transition to lifecycle support services.

    Related Products

    Standard Series Platforms

    For established test requirements, Deepvac's Standard Series offers pre-engineered T Series and C Series platforms.

    View Standard Series
    Engineering Services

    Design, Testing & Integration

    Deepvac provides control systems design, mechanical engineering, testing services, and lifecycle support alongside chamber development.

    Explore Engineering Services
    FAQ

    Custom TVAC Questions

    Ready to Discuss Your Custom TVAC Project?

    Contact Deepvac to start the technical consultation process and define the right system architecture for your application.

    Submit detailed system requirementsRequest a Technical Consultation

    Prefer a direct conversation?